www.usa-automation.net
19
'26
Written on Modified on
Direct Drive Frameless Motors for Non-Aerial Gimbal Design
ALVA Industries' SlimTorq™ slotless frameless motors give non-aerial gimbals backlash-free direct drive, zero cogging torque and a large through-bore for cable routing.
www.alvaindustries.com

Gimbals that stabilise and point cameras or sensors must combine fast response, precise positioning and room for cables, slip rings and, in some cases, cooling lines passing through their rotating axes. ALVA Industries has set out why direct drive actuation suits non-aerial gimbals and how its slotless frameless motors, built with its FiberPrinting™ stator technology, address these requirements.
Gimbal actuation: geared versus direct drive
Motion systems for gimbals generally follow one of two architectures: a motor coupled to a gearbox, or a direct drive motor acting on the axis without transmission. In aerial gimbals, mass is often the deciding factor. Once weight is less critical, as in non-aerial designs, dynamic performance and precision become the main selection criteria.
According to ALVA Industries, a direct drive configuration offers higher peak torque, which translates into greater responsiveness, and shorter settling times after a commanded move. Because there is no gearbox in the drivetrain, there is also no backlash to compensate for in the control loop, allowing more precise positioning and smoother tracking.
Large through-bore for cable routing and slip rings
A direct drive frameless motor typically offers a larger central opening than a comparable geared or slotted solution. In a gimbal, this through-bore can be used to pass cables straight through the axis rather than routing them around the motor. Slip ring selection is less constrained by the space available inside the motor, and where sensors require active cooling, refrigeration lines can be routed through the same bore. The result is a more compact mechanical layout with fewer external cable runs.
How slotless frameless motors avoid cogging torque
SlimTorq™ is a slotless, thin-section frameless motor series and, according to ALVA Industries, non-aerial gimbals are among its most common applications. Removing the iron teeth from the stator eliminates cogging torque, the periodic torque variation caused by magnets aligning with stator slots, which is a key factor in smooth low-speed motion and accurate pointing.
Slotless motors traditionally trade this smoothness for lower torque density. ALVA Industries counters this with its FiberPrinting™ manufacturing process, which achieves a high copper fill factor and non-skewed stator windings, combined with a Halbach array rotor that concentrates magnetic flux. The company states that the resulting motor constant and torque density are comparable to slotted designs. The thin stator and rotor also enlarge the inner diameter available for the through-bore.
The motors are three-phase BLDC types that can be driven by most off-the-shelf controllers in trapezoidal, sinusoidal or field-oriented control modes, with or without sensor feedback. Because of their low inductance, the switching frequency of the drive must be selected accordingly. The series is available in a Lite version optimised for low mass and a Max version optimised for torque and motor constant.
Custom motors for specific gimbal envelopes
Where no standard size fits an application, ALVA Industries states that the flexibility of FiberPrinting™ allows it to develop custom motors to match the required space envelope and performance.
Additional Context
This section details technical specifications and competitive benchmarking not included in the original product announcement.
Precision gimbals and pointing systems commonly use either geared drives, often with strain wave or planetary gearboxes, or direct drive frameless torque motors. Gear stages increase output torque but introduce backlash, torsional compliance and friction, which limit stiffness and bandwidth in closed-loop pointing. Direct drive removes these transmission effects, at the cost of requiring a motor that delivers the full axis torque itself.
Frameless torque motors fall into slotted, iron-core designs, which offer high torque density but exhibit cogging that is often reduced by skewing at the expense of torque constant, and slotless designs, which eliminate cogging but have a larger magnetic air gap. Halbach magnet arrays and higher winding fill factors are established engineering methods for recovering torque density in slotless machines.
Edited by Sucithra Mani, Induportals editor – adapted by AI.
www.alvaindustries.com

